C-130 PSI Structural Specialists

Company: 
PowerHouse Resources International
Category: 
Maintenance
Job Type: 
Permanent
City: 
Elizabeth City
State: 
North Carolina
Country: 
USA

The Contractor shall provide and maintain as required by the contract at least two qualified Structural Specialists. The C-130 PSI Structural Specialists must meet all qualifications and demonstrate experience performing the following work:

  • Each specialist shall have at least 5 years of designing repair schemes for structural issues outside of the C-130 structural repair manuals or similar and have documented experience with aircraft major overhaul maintenance and repair experience on C-130 series aircraft or similar aircraft.
  • Specialists shall be able to read and interpret engineering and technical data. The Contractor shall initiate design for non-standard repairs with final approval resting with the Government.

In addition, the C-130 PSI Structural Specialist must have the following basic personnel requirements in performance of this contract:

  • Possess High School diploma or equivalent.
  • Capable of performing tasks that frequently require: lifting, reaching, bending, walking, pulling, sitting, standing, crouching, stooping, kneeling, and stretching for
    prolonged periods of time. Must be capable of performing tasks in
    cramped, awkward, and strained positions and/or climbing up and down ladders, work platforms, scaffolding, and aircraft structures. Must be capable of carrying items up to 40 pounds or, for heavier objects, must seek assistance of other workers or weight lifting devices. Must be capable of wearing cumbersome personal protective equipment for HAZMAT operations.
  • Possess knowledge of basic computer skills sufficient to use Government computer system to access various technical references for airframe repairs and Government training requirements.
  • Document maintenance as per Quality Assurance (QA) and established regulatory requirements.
  • Comply with work order timekeeping system procedures.
  • Maintain
    high state of cleanliness and utilize a clean-as-you-go process when
    executing maintenance duties. Perform regular Foreign Object Damage
    (FOD) walk-downs.
  • Maintain situational awareness, stay cognitive-focused, and mitigate risks.
  • Comply with processes and procedures as per DHS/DOD documents and publications.
  • Immediately report missing, lost, found, or unattended tools to the supervisor. Maintain and control tools IAW USCG
    tool control policy and instructions. Inventory and inspect tools on a
    regular basis to identify when to replace worn or broken tools and
    report the need for replacement tools to the supervisor.
  • Clean
    work area as necessary, assuring all hazardous materials are properly
    stored; Handle hazardous materials, expired materials and wastes in
    accordance with applicable laws and regulatory requirements.
  • Comply
    with safety rules and procedures and perform work in a manner that
    enhances the safety of the work area. Promptly report accidents,
    injuries, safety, violations, and/or unsafe practices or procedures to
    supervisor.
  • Complete required training as stated by Federal regulations, State regulations, and requirements in accordance with the GFR DCMA INST 8210.l(series)/ COMDTINST M13020.3(series) for the job/processes performed; and have documentation on file for courses completed.
  • USCG Base Elizabeth City owns and is responsible for the environmental permits required to operate onboard the facility. The USCG ALC is a tenant of Base Elizabeth City, therefore, all ALC operations are covered by the Base's environmental compliance permits. Prior to performing industrial work, personnel must be trained in USCG ALC environmental policies and procedures. As a minimum, personnel shall be trained in the requirements of ALC Instructions 5224.20 (series) Waste and Recycling Management, 5224.21 (series) Hazardous Materials Management and 5224.22 (series) Spill Prevention and Emergency Response. Personnel shall follow all ALC Standard Operating Procedures that include environmental compliance requirements. Guidance posters and charts are located throughout the facility and should be followed, as applicable.
  • 40 CFR 273.36 requires that ALL (industrial, office, etc.) employees be familiar with the facility' s Universal Waste (UW) (batteries and lamps) procedures and emergency response. For convenience, a training presentation for UW Management at USCG ALC is available on the ALC portal or from the ALC Environmental Management Representative.
  • 40 CFR 112.7 requires that all employees that handle fuels be trained in the site-specific Spill Prevention, Control and Countermeasures (SPCCP) plan. Required training and site#173; specific training materials are provided by Base Elizabeth City. Facilities Response Plan (FRP) Training is also provided. In addition, CGTO PG-85-00-170 USCG Fuel Handling Procedures (Aircraft) section 11. B. addresses the training requirements for aviation fuel handlers.
JobReq: 

See Job Description

First posted: 
9/6/2017 1:58:06 PM

About D.O.M. Magazine

D.O.M. magazine is the premier magazine for aviation maintenance management professionals. Its management-focused editorial provides information maintenance managers need and want including business best practices, professional development, regulatory, quality management, legal issues and more.

The digital version of D.O.M. magazine is available for free on all devices (iOS, Android, and Amazon Kindle).

More Info

Joe Escobar (jescobar@dommagazine.com)
Editorial Director
920-747-0195

Greg Napert (gnapert@dommagazine.com)
Publisher, Sales & Marketing
608-436-3376

Bob Graf (bgraf@dommagazine.com)
Director of Business, Sales & Marketing
608-774-4901